Reloading a Snort configuration
===============================
Snort now supports reloading a configuration in lieu of restarting Snort in
so as to provide seamless traffic inspection during a configuration change.
A separate thread will parse and create a swappable configuration object while
the main Snort packet processing thread continues inspecting traffic under the
current configuration.  When a swappable configuration object is ready for use,
the main Snort packet processing thread will swap in the new configuration to
use and will continue processing under the new configuration.  Note that for
some preprocessors, existing session data will continue to use the configuration
under which they were created in order to continue with proper state for that
session.  All newly created sessions will, however, use the new configuration.


Enabling support
================
To enable support for reloading a configuration, add "--enable-reload" to
configure when compiling.

There is also an ancillary option that determines how Snort should behave
if any non-reloadable options are changed (see "Non-reloadable configuration
options" below).  This option is enabled by default and the behavior is for
Snort to restart if any non-reloadable options are added/modified/removed.
To disable this behavior and have Snort exit instead of restart, add
"--disable-reload-error-restart" in addition to "--enable-reload" to configure
when compiling.

NOTE: This functionality is not currently supported in Windows.


Reloading a configuration
=========================
First modify your snort.conf (the file passed to the '-c' option on the
command line).

Then, to initiate a reload, send Snort a SIGHUP signal, e.g.

$ kill -SIGHUP <snort pid>

NOTE: If reload support is not enabled, Snort will restart (as it always has)
upon receipt of a SIGHUP.

NOTE: An invalid configuration will still result in Snort fatal erroring, so
you should test your new configuration before issuing a reload, e.g.

$ snort -c snort.conf -T


Non-reloadable configuration options
====================================
There are a number of option changes that are currently non-reloadable because
they require changes to output, startup memory allocations, etc.  Modifying any
of these options will cause Snort to restart (as a SIGHUP previously did) or
exit (if "--disable-reload-error-restart" was used to configure Snort).

Reloadable configuration options of note:
* Adding/modifying/removing text rules and variables are reloadable.
* Adding/modifying/removing preprocessor configurations are reloadable (except
  as noted below).

Non-reloadable configuration options of note:
* Adding/modifying/removing shared objects via dynamicdetection, dynamicengine
  and dynamicpreprocessor are not reloadable, i.e. any new/modified/removed
  shared objects will require a restart.
* Any changes to output will require a restart.

Changes to the following options are not reloadable:

attribute_table
config alertfile
config asn1
config chroot
config daemon
config detection_filter
config flexresp2_attempts
config flexresp2_interface
config flexresp2_memcap
config flexresp2_rows
config flowbits_size
config interface
config logdir
config max_attribute_hosts
config nolog
config no_promisc
config pkt_count
config rate_filter
config read_bin_file
config set_gid
config set_uid
config snaplen
config threshold
dynamicdetection
dynamicengine
dynamicpreprocessor
output

In certain cases, only some of the parameters to a config option or
preprocessor configuration are not reloadable.  Those parameters are
listed below the relevant config option or preprocessor.

config ppm: max_rule_time <int>
 rule-log
config profile_rules
 filename
 print
 sort
config profile_preprocs
 filename
 print
 sort
preprocessor dcerpc2
 memcap
preprocessor frag3_global
 max_frags
 memcap
 prealloc_frags
 prealloc_memcap
preprocessor perfmonitor
 file
 snortfile
preprocessor sfportscan
 memcap
 logfile
preprocessor stream5_global
 memcap
 max_tcp
 max_udp
 max_icmp
 track_tcp
 track_udp
 track_icmp

